Vertical or Horizontal Smoker
Moderator: TBBQF Deputies
- AzViper
- Pilgrim
- Posts: 10
- Joined: Sun Apr 09, 2017 10:12 pm
- Location: Arizona
- Contact:
Vertical or Horizontal Smoker
Thanks for allowing me to join. I am a fabricator and building a quality smoker is not out of the question. The smoker will be for our backyard use. I have gotten my hands on a 60 gallon vertical 24 inches in diameter air compressor tank of which I could make a vertical smoker with a fire box off to one side or build a horizontal reverse flow smoker. Looking on Youtube and do not see many vertical built smokers from either air tanks or propane tanks.
My question for the pros is the vertical due to the legs already in place would be easier to get built. What are the pros and cons of both the vertical & horizontal smoker?
As I said I am a fabricator and build custom gold mining gear so building this smoker is not a problem, but I am in over my head on building a smoker. Have watched many videos on reverse flow smoker.
12 inch Trommel
My question for the pros is the vertical due to the legs already in place would be easier to get built. What are the pros and cons of both the vertical & horizontal smoker?
As I said I am a fabricator and build custom gold mining gear so building this smoker is not a problem, but I am in over my head on building a smoker. Have watched many videos on reverse flow smoker.
12 inch Trommel
Last edited by AzViper on Thu Apr 20, 2017 6:18 am, edited 4 times in total.
I am a UAV pilot keeping a watchful eye below.
https://vimeo.com/198627252
https://vimeo.com/198627252
- k.a.m.
- Chuck Wagon
- Posts: 3746
- Joined: Mon Jun 25, 2012 6:38 pm
- Contact:
Re: Vertical or Horizontal Smoker
Some folks like vertical smokers because their foot print is less. I prefer horizontal offsets because I like the options of meat placement at any given time. While I have built quite a few reverse flow cookers I prefer a cooker with tuning plates. My big competition cooker is a Hybrid that I designed it can cook either way but I never use the reverse flow option. My smaller competition cooker is a 24" x 55" and it is straight tuning plates.
- AzViper
- Pilgrim
- Posts: 10
- Joined: Sun Apr 09, 2017 10:12 pm
- Location: Arizona
- Contact:
Re: Vertical or Horizontal Smoker
K.A.M.
Thank you for the reply. During some research I came across Feldon's BBQ Pit/Smoker Build Calculator. This appears to be very helpful as I had many questions in regards to the fire box.
Thank you for the reply. During some research I came across Feldon's BBQ Pit/Smoker Build Calculator. This appears to be very helpful as I had many questions in regards to the fire box.
I am a UAV pilot keeping a watchful eye below.
https://vimeo.com/198627252
https://vimeo.com/198627252
- k.a.m.
- Chuck Wagon
- Posts: 3746
- Joined: Mon Jun 25, 2012 6:38 pm
- Contact:
Re: Vertical or Horizontal Smoker
AzViper wrote:K.A.M.
Thank you for the reply. During some research I came across Feldon's BBQ Pit/Smoker Build Calculator. This appears to be very helpful as I had many questions in regards to the fire box.
You are very welcome Sir.
If you have questions about the calculator you can use the email at the bottom my email is attached to the calculator I helped design it.
- AzViper
- Pilgrim
- Posts: 10
- Joined: Sun Apr 09, 2017 10:12 pm
- Location: Arizona
- Contact:
Re: Vertical or Horizontal Smoker
After reading more I am going to build a horizontal reverse flow smoker. Hopefully I will have the tank this weekend. I have to remove the motor and compressor head from the tank. Its an Ingersoll Rand compressor that the head is shot and has not been in use for over 10 years. Had a dryer attached to it to remove any moisture so the tank should be in great condition. I had a horizontal Ingersoll Rand screw compressor that sat for years, it ended up in a salvage yard.
Last edited by AzViper on Wed Apr 12, 2017 7:18 pm, edited 1 time in total.
I am a UAV pilot keeping a watchful eye below.
https://vimeo.com/198627252
https://vimeo.com/198627252
- Boots
- Wordsmith
- Posts: 4717
- Joined: Sat Jul 23, 2011 12:16 pm
- Location: McKinney, Texas, USA!
- Contact:
Re: Vertical or Horizontal Smoker
Might just want to do a good initial burnout in it in case there's a spray sealant or rust inhibitor. Just food get thought. Not galvanized right?
BE WELL, BUT NOT DONE
Hank: "Do you know how to jumpstart a man's heart with a downed power line?"
Bobby: "No."
Hank: "Well, there's really no wrong way to do it."
Hank: "Do you know how to jumpstart a man's heart with a downed power line?"
Bobby: "No."
Hank: "Well, there's really no wrong way to do it."
- AzViper
- Pilgrim
- Posts: 10
- Joined: Sun Apr 09, 2017 10:12 pm
- Location: Arizona
- Contact:
Re: Vertical or Horizontal Smoker
Its painted on the outside of the original paint from the factory. Will not know until I clean and cut into it. I doubt that its galvanized.
I am a UAV pilot keeping a watchful eye below.
https://vimeo.com/198627252
https://vimeo.com/198627252
- AzViper
- Pilgrim
- Posts: 10
- Joined: Sun Apr 09, 2017 10:12 pm
- Location: Arizona
- Contact:
Re: Vertical or Horizontal Smoker
I am curious as to what elevation will do to these calculated numbers from the calculator for the Chimney Size, Air Inlet Size, and Airbox To Cooking Camber Size.
Where I am located it's 2300 feet above sea level.
Where I am located it's 2300 feet above sea level.
I am a UAV pilot keeping a watchful eye below.
https://vimeo.com/198627252
https://vimeo.com/198627252
- AzViper
- Pilgrim
- Posts: 10
- Joined: Sun Apr 09, 2017 10:12 pm
- Location: Arizona
- Contact:
Re: Vertical or Horizontal Smoker
In this drawing I show the cutout in the firebox into the cooking chamber. I am allowing the bottom of the cutout to be just over 1 inch above the bottom of the chamber as a grease stop. Is this correct so grease does not flow back into the firebox?
Last edited by AzViper on Wed Apr 12, 2017 7:32 pm, edited 1 time in total.
I am a UAV pilot keeping a watchful eye below.
https://vimeo.com/198627252
https://vimeo.com/198627252
- k.a.m.
- Chuck Wagon
- Posts: 3746
- Joined: Mon Jun 25, 2012 6:38 pm
- Contact:
Re: Vertical or Horizontal Smoker
AzViper wrote:I am curious as to what elevation will do to these calculated numbers from the calculator for the Chimney Size, Air Inlet Size, and Airbox To Cooking Camber Size.
Where I am located it's 2300 feet above sea level.
There have been many a cooker built using the calculator. The 1/3 rule it is based on works in upper altitudes just fine. The 1" bridge is a good idea.
- AzViper
- Pilgrim
- Posts: 10
- Joined: Sun Apr 09, 2017 10:12 pm
- Location: Arizona
- Contact:
Re: Vertical or Horizontal Smoker
k.a.m. wrote:AzViper wrote:I am curious as to what elevation will do to these calculated numbers from the calculator for the Chimney Size, Air Inlet Size, and Airbox To Cooking Camber Size.
Where I am located it's 2300 feet above sea level.
There have been many a cooker built using the calculator. The 1/3 rule it is based on works in upper altitudes just fine. The 1" bridge is a good idea.
Kevin, Thank you for the reply. I am sure I will have questions as the build begins. Not sure when that will be as I am trying to finish up a 44'x 18' porch and the surrounding areas. Here are the number I arrived with the current tank. Any suggestions?
I am a UAV pilot keeping a watchful eye below.
https://vimeo.com/198627252
https://vimeo.com/198627252
- AzViper
- Pilgrim
- Posts: 10
- Joined: Sun Apr 09, 2017 10:12 pm
- Location: Arizona
- Contact:
Re: Vertical or Horizontal Smoker
I am a UAV pilot keeping a watchful eye below.
https://vimeo.com/198627252
https://vimeo.com/198627252
- k.a.m.
- Chuck Wagon
- Posts: 3746
- Joined: Mon Jun 25, 2012 6:38 pm
- Contact:
- AzViper
- Pilgrim
- Posts: 10
- Joined: Sun Apr 09, 2017 10:12 pm
- Location: Arizona
- Contact:
Re: Vertical or Horizontal Smoker
Going to cut out the plates with a CNC waterjet, this eliminating any issues in keeping the plates flat and true to within .005.
I am a UAV pilot keeping a watchful eye below.
https://vimeo.com/198627252
https://vimeo.com/198627252
- AzViper
- Pilgrim
- Posts: 10
- Joined: Sun Apr 09, 2017 10:12 pm
- Location: Arizona
- Contact:
Re: Vertical or Horizontal Smoker
Boots wrote:Might just want to do a good initial burnout in it in case there's a spray sealant or rust inhibitor. Just food get thought. Not galvanized right?
Once I have the tank in hand will check the inside of the tank.
I am a UAV pilot keeping a watchful eye below.
https://vimeo.com/198627252
https://vimeo.com/198627252
Return to “Custom Built Pits, Build Your Own Pit & Pit Modifications”
Who is online
Users browsing this forum: No registered users and 30 guests