I bought a Probe Port and it says to drill the final hole at 27/32", is there an equivalent measurement too that, I can't find a 27/32! I was wondering if there is a step drill bit I can use and what size would be equal, I dont see 27/32 on any step bit!
this is the Probe Port I bought,
https://www.amazon.com/gp/product/B06WW ... UTF8&psc=1
PROBE PORT HELP INSTALL
Moderator: TBBQF Deputies
- Michael0506
- Wrangler
- Posts: 52
- Joined: Fri Oct 12, 2018 6:51 pm
- Contact:
- Papa Tom
- Deputy
- Posts: 6775
- Joined: Sat Jun 30, 2007 9:40 am
- Location: Oak Point, TX
- Contact:
Re: PROBE PORT HELP INSTALL
Well 26/32 is 13/16 1/32 smaller than it calls for 24/32 is 3/4 3/32 small than called for they make a tapered reaming bit (like a step bit but no steps) that you could use to enlarge to fit....
27/32 is .84375" and my step bit (from a Harbor Freight set) has a step that is .855" only .011 larger that is darn close.
Hope this helps.
27/32 is .84375" and my step bit (from a Harbor Freight set) has a step that is .855" only .011 larger that is darn close.
Hope this helps.
tarde venientibus ossa....
- OldUsedParts
- Deputy
- Posts: 21616
- Joined: Sun May 15, 2011 7:09 pm
- Location: Montgomery, Texas
- Contact:
Re: PROBE PORT HELP INSTALL
Excuse my ignorance but does it really make that much difference as long as the probe will fit with not too much wobble
I am determined to sustain myself as long as possible & die like a soldier who never forgets what is due to his own honor & that of his country—Victory or Death. William Barret Travis - Lt. Col. comdt "The Alamo"
- Papa Tom
- Deputy
- Posts: 6775
- Joined: Sat Jun 30, 2007 9:40 am
- Location: Oak Point, TX
- Contact:
Re: PROBE PORT HELP INSTALL
OldUsedParts wrote:Excuse my ignorance but does it really make that much difference as long as the probe will fit with not too much wobble
And then there's OUP who doesn't seem to mind if his probe wobbles a bit........
tarde venientibus ossa....
- OldUsedParts
- Deputy
- Posts: 21616
- Joined: Sun May 15, 2011 7:09 pm
- Location: Montgomery, Texas
- Contact:
Re: PROBE PORT HELP INSTALL
Papa Tom wrote:OldUsedParts wrote:Excuse my ignorance but does it really make that much difference as long as the probe will fit with not too much wobble
And then there's OUP who doesn't seem to mind if his probe wobbles a bit........
I DO CARE but I have an Anti-Wobble Device for such matters
I am determined to sustain myself as long as possible & die like a soldier who never forgets what is due to his own honor & that of his country—Victory or Death. William Barret Travis - Lt. Col. comdt "The Alamo"
-
- Bandolero
- Posts: 987
- Joined: Thu Aug 03, 2017 10:15 am
- Contact:
Re: PROBE PORT HELP INSTALL
27/32" is kind of an odd ball bit. Mostly used by machinist. I've got most of my dad's bits but 25/32" was as close as I have. Did find one on e-bay however. Not a bad price even if it's a one time use.
https://www.ebay.com/itm/Bosch-HC2137-S ... :rk:3:pf:0
https://www.ebay.com/itm/Bosch-HC2137-S ... :rk:3:pf:0
"The days I keep my expectations low and my gratitude high, I have really good days."
Ray Wylie Hubbard
Ray Wylie Hubbard
- Michael0506
- Wrangler
- Posts: 52
- Joined: Fri Oct 12, 2018 6:51 pm
- Contact:
Re: PROBE PORT HELP INSTALL
Papa Tom wrote:Well 26/32 is 13/16 1/32 smaller than it calls for 24/32 is 3/4 3/32 small than called for they make a tapered reaming bit (like a step bit but no steps) that you could use to enlarge to fit....
27/32 is .84375" and my step bit (from a Harbor Freight set) has a step that is .855" only .011 larger that is darn close.
Hope this helps.
Thank you!
- Michael0506
- Wrangler
- Posts: 52
- Joined: Fri Oct 12, 2018 6:51 pm
- Contact:
Re: PROBE PORT HELP INSTALL
Thanks for all the great info and yes I hate wobble!
Return to “Custom Built Pits, Build Your Own Pit & Pit Modifications”
Who is online
Users browsing this forum: No registered users and 54 guests